DXLink TX X00 Series firmware
Question:
DXLink TX X00 Series firmware
Answer:
DXLink TX X00 Series Firmware v1.8.47
Current upgrade firmware for DXLink TX units.
Release Notes:
Release Notes
DXLink HDMI Transmitter Module Firmware
(Enova DGX 100 Series Compatible)
!!IMPORTANT: READ PROGRAMMING INFORMATION SECTION BELOW
IN REGARD TO UPGRADING OLDER FIRMWARE VERSIONS!!
!!This firmware version requires Enova DGX 100 Series
compatibility on connected Enova DGX systems!!
!!!Please reference the Enova DGX Board and Endpoint
Compatibility Instructions on the AMX.com product
page for more information!!!
FG#:
FG1010-300 (AVB-TX-HDMI-DXLINK, DXLink HDMI Transmitter Module)
FG1010-310 (DX-TX, DXLink Multi-Format Transmitter Module)
FG1010-320-BL (DX-WP, DXLink Multi-Format Wallplate Transmitter)
FG1010-320-WH (DX-WP, DXLink Multi-Format Wallplate Transmitter)
FG1010-325-BL (DX-DWP, DXLink Multi-Format Decor Style Wallplate Transmitter)
FG1010-325-WH (DX-DWP, DXLink Multi-Format Decor Style Wallplate Transmitter)
Release Date: 08/06/2018
Current Released Firmware: v1.8.47
SW1010_3XX_AVB_KIT_DXLINK_TX_v1_8_47.kit
----------------------------------------------------------
Table of Contents
----------------------------------------------------------
1. Prerequisites
2. Features added in this release
3. Fixes in this release
4. Notable Points
5. Programming Information
----------------------------------------------------------
1. Prerequisites
----------------------------------------------------------
- DXLink TX v1.6.7 (or later) must be loaded on the DXLink
Transmitters to upgrade
- DXLink RX v1.13.28 (or later) must be used on the DXLink
Receiver for best performance with this TX version
- Enova DGX 800/1600/3200/6400 must have v3.2.4 (or later)
to allow use of the new ICSLAN feature and async status
improvements in this release. Else v3.0.20 (or later)
The DGX 100 Series Master FW should be:
- SW2106_NX-X200_Master_v1_4_86.kit(or later)
- Enova DGX 8/16/32/64 enclosures need Enova DGX 8/16/32/64
FW v2.2.8 (or later) and Master FW:
- SW1056_Master_v4_2_395.KIT (NI-Series) Shows in Online
Tree as "NI Master"
- SW2106_NX-X200_Master_v1_3_106.kit (NX-Series) Shows
in Online Tree as "DGX Master"
- NetLinx Studio v4.3.1519
- DGX Configuration Software v1.0.6 or later
----------------------------------------------------------
2. Features added in this release
----------------------------------------------------------
- VIDIN_EDID changes are now persistent, will keep the
previous settings after a reboot
== Previously released in v1.8.26 ==========================
- Added ability to set TX ICSLAN port to be on the public
or private network. Added new DGX ICSP command:
5002:x:0 ENDPOINT_TX_ICSLAN_PORT-<PRIVATE|PUBLIC>
Where x is the input channel connected to the TX.
!!NOTE: This requires DGX v3.2.4 (or later)!!
----------------------------------------------------------
3. Fixes in this release
----------------------------------------------------------
Fixed video flickering issue
== Previously released in v1.8.46 =========================
Fixed issues in point to point using HDMI retractor cable
== Previously released in v1.8.43 =========================
- Added VIDIN_PREF_EDID command to work with HDMI input
- Persistence added for VIDIN_PREF_EDID if All Resolutions
set on HDMI input
== Previously released in v1.8.41 =========================
- Persistent setting of VIDIN_EDID-All Resolutions
== Previously released in v1.8.38 =========================
- Fixed an issue where dxlink input of DVX would flicker with
VGA Laptop to MFTX, going from duplicate to extend mode
== Previously released in v1.8.37 =========================
Fixed an issue where MacBooks would not sync up with video
very well.
== Previously released in v1.8.35 =========================
Fixed an issue where a message to the DGX was incorrect
== Previously released in v1.8.33 =========================
Fixed long term video issue where output may get stuck showing
black on the display
Fixed an issue where some 4k sinks would cause no video to be
present in a point to point setup. MFTX -> RX -> 4k sink setup.
== Previously released in v1.8.32 ==========================
Fixed an issue where MFTX is randomly not coming online after
a DGX reboot
== Previously released in v1.8.31 ==========================
Fixed video flicker when VGA was transmitted and HDMI was
plugged in or unplugged.
== Previously released in v1.8.29 ==========================
Fixed issue that could cause MFTX to not come online.
== Previously released in v1.8.29 ==========================
Fixed issue that caused no video.
== Previously released in v1.8.28 ==========================
Fixed random offline/online events.
== Previously released in v1.8.26 ==========================
- Fixed issue where WP/DWP don't come online in AutoSetup
- Fixed video flicker issue caused by certain cameras or
other DVI sources
- Improved audio/video detection with difficult sources
- Fixed colorspace and video/audio detection issues when
connected to a DXLink 4K Input card
- Fixed IR TX LED issue and IR one way serial reliability
- Fixed instances where the MFTX status (via ICSP or Web
Interface) could get out of sync
- Corrected some differences in status reporting (compared
to other TX products) when no signal is present
----------------------------------------------------------
4. Notable Points
----------------------------------------------------------
- PLEASE READ the documentation in regard to the DIP
switches located on the bottom of the Tx/Rx modules
before attempting to connect to the network
- After a FACTORYAV (ICSP) or RESET FACTORY (telnet)
command, a reboot of the endpoint is required.
----------------------------------------------------------
5. Programming Information
----------------------------------------------------------
!!This firmware version requires Enova DGX 100 Series
compatibility on connected Enova DGX systems!!
- !!!Please reference the Enova DGX Board and Endpoint
Compatibility Instructions on the AMX.com product
page for more information!!!
--UPGRADING-----------------------------------------------
!! Important–Two loads of this kit MAY be required if !!
!! upgrading from firmware earlier than v1.6.7 !!
!! !!
!! 1. Transfer kit v1.8.47 to the TX. If upgrading from !!
!! a version earlier than 1.6.7, it will abort due to!!
!! a memory error. If so, proceed to step 2 !!
!! !!
!! 2. Reboot the TX (via telnet or power cycle) then !!
!! check the firmware versions in the Online Tree: !!
!! !!
!!eg. 32002 - DXLINK-HDMI-MFTX-v1.8.47 !!
!! [OID=1] - MQX (v3.62) !!
!! [OID=2] - DXLINK Boot (v1.8.47) !!
!! [OID=3] - DXLINK App (v1.8.47) !!
!! [OID=5] - DXLINK Link (3.0.6.0) !!
!! !!
!! 3. If the Link version is still not up to date, then !!
!! transfer v1.8.45 again to completely the update of!!
!! the final component. If the FW is up to date then !!
!! no other kit transfers are required. !!
==========================================================
- PLEASE reference Appendix A (Upgrading the Firmware) in the
DXLink Instruction Manual for more information.